crystal
Senior Member
Joined:September 2014
Posts: 367 
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Mar 12, 2017 9:06:00 GMT
|
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Mar 12, 2017 8:27:51 GMT
 cragLike others have already said the most important thing is getting used to not reaching for the "stinkies". Don't worry about dropping the nic levels until you feel comfortable to do so. You will find your own sweet spot for nic levels and flavours eventually. Loads of help from everyone on here if and when you need it. Good luck starting on your new life without the fags. 
|
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Feb 11, 2017 9:15:39 GMT
Have a gud'un  |
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Feb 3, 2017 9:57:36 GMT
|
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Feb 3, 2017 9:12:10 GMT
|
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Feb 2, 2017 9:08:11 GMT
VapingBad thebishmanThanks for all your help guys. I think VapingBad was right, rewicked this morning with quite a lot more cotton forced into the juice wells and so far, no leaks and seems to be wicking better too. Was getting lots of spitting before now it's gone. Thanks again
|
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Feb 1, 2017 10:45:33 GMT
VapingBad I'm using 100% vg, it doesn't seem to be a wicking problem, just a seal or seating prob.
|
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Feb 1, 2017 10:38:45 GMT
thebishman Thanks for the idea. I thought that so I changed the wick and put quite a lot more in the juice channels, no problems there until I fill above the top of the atomizer where it screws into the top section, then I might as well pour juice out of the bottle.
|
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Feb 1, 2017 10:19:27 GMT
Got myself one of these tanks to see what all the good reviews are all about.
Even though it's a juice guzzler I'm very impressed with the stock coils, no leaks but they do get gunked up within a couple of days.
The problems occur with the rebuildable section. Filling above the top of the atty it leaks like mad so can only partially fill the thing. Tried different o rings and everything else to seal that thread without any success.
Anyone else had the same problem, if so, any ideas how to fix it?
|
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Nov 10, 2016 16:44:33 GMT
Thanks to all for the best wishes  |
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Sept 27, 2016 9:14:16 GMT
Thought i would see if my baby cnc could engrave. Quite suprised with the results.  Looking good @windows What cutter are you using? |
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Sept 25, 2016 16:38:26 GMT
 I'm attempting a trial print of this. Seems a better design than the mkI. I will be using Big Al's Side Mount 6S PWM Board from Modmaker. |
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Sept 25, 2016 16:30:33 GMT
Fasttech do Velocity clone with a bottom feeder pin included, its a grub screw that you take out if that's any good to you geordie_vaper. I have one on my homemade squonker. |
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Sept 23, 2016 10:07:54 GMT
Got a few clone DNA30s, hope that doesn't include them  |
|
crystal
Senior Member
Joined:September 2014
Posts: 367
Location:
Likes: 308
Recent Posts
Last Online Jun 17, 2018 8:55:07 GMT
|
Post by crystal on Sept 23, 2016 9:46:53 GMT
ghostrider1971It's difficult to find vendors that sell vaping supplies there, that depends where you go though. I go SW Philippines every year and what I'm told, the nearest is in Cebu which is a boat ride away. Have a nice time there, Red Horse and Tanduay Rum are my favorite tipples there. 
|
|
