Interesting Bit Of Kit From Cthulhu

[Get Off My Cloud]

Q: How do you turn one of these into a squonker?


A: With one of these.


Peaked my interest, not only could you slap it on a tube mech but you could also put it on any non-squonk box right?
Has a 7.1ml capacity bottle.
One thing to note they say 22mm-24mm in the description but that's kind of right and kind of wrong, it looks like a 22mm is the minimum size atty you need to create a seal on the top part but the adapter itself is 24mm wide so not going to work really on a 22mm tube unless you want overhang.

www.3fvape.com/misc/20724-authentic-cthulhu-squonk-genius-adapter-for-22mm-24mm-rda-silver-stainless-steel-silicone-71ml.html#.Wjpg5TfLjIU

[phtumshk]

Looks a bit more stylish than the old fountain RDA sqounk thing from a while back.
Im taking its 24mm dia tho so Im out.

EDIT:Looks like you fill it through the kidney shaped windows on the top and seal it with your RDA, nice touch.

[yourgurnard]

As soon as this gets cloned, I'm on one!!
Tho' I will say exactly the same as I said for the Mesh RDA......'Clone it.....& shrink it to 16mm'!!

[Get Off My Cloud]

Dec 20, 2017 19:40:26 GMT yourgurnard said:

As soon as this gets cloned, I'm on one!!
Tho' I will say exactly the same as I said for the Mesh RDA......'Clone it.....& shrink it to 16mm'!!

Yeah a range of sizes so it can fit flush  on a variety of tubes would be good, i think at 16mm the bottle capacity would be reduced too much for it's current height to be a useful bit of kit though, they would have to increase the height of the device to have it accommodate a decent amount of juice.

[beedee]

Interesting one, Get Off My Cloud, looks better than the last attempt to create a bolt on squonk section.

[yourgurnard]

Dec 20, 2017 21:02:08 GMT Get Off My Cloud said:

Dec 20, 2017 19:40:26 GMT yourgurnard said:

As soon as this gets cloned, I'm on one!!
Tho' I will say exactly the same as I said for the Mesh RDA......'Clone it.....& shrink it to 16mm'!!

Yeah a range of sizes so it can fit flush  on a variety of tubes would be good, i think at 16mm the bottle capacity would be reduced too much for it's current height to be a useful bit of kit though, they would have to increase the height of the device to have it accommodate a decent amount of juice.

Don't need a lot of juice (TPD-compliant, Me!!! ...) just wanna 'squonk-interface' twixt I-stick 30w & L16!!!

[Lee]

Be nice to have the rx's back in use with this converter
Nothing worse than poxy single battery mods

[phtumshk]

Dec 20, 2017 23:48:55 GMT Lee said:

Be nice to have the rx's back in use with this converter
Nothing worse than poxy single battery mods

would look quite fetchin on a rolo75.

[phtumshk]

Dec 20, 2017 23:26:22 GMT yourgurnard said:

Dec 20, 2017 21:02:08 GMT Get Off My Cloud said:

Yeah a range of sizes so it can fit flush  on a variety of tubes would be good, i think at 16mm the bottle capacity would be reduced too much for it's current height to be a useful bit of kit though, they would have to increase the height of the device to have it accommodate a decent amount of juice.

Don't need a lot of juice (TPD-compliant, Me!!! ...) just wanna 'squonk-interface' twixt I-stick 30w & L16!!!

I was looking at me old istick 20s was thinking of putting the board in a squonker but they only fire at an ohm.
What is the spec on the 30 boards how low does it fire?

[Get Off My Cloud]

Dec 21, 2017 0:38:56 GMT phtumshk said:

Dec 20, 2017 23:26:22 GMT yourgurnard said:

Don't need a lot of juice (TPD-compliant, Me!!! ...) just wanna 'squonk-interface' twixt I-stick 30w & L16!!!

I was looking at me old istick 20s was thinking of putting the board in a squonker but they only fire at an ohm.
What is the spec on the 30 boards how low does it fire?

Minimum resistance 0.4ohm
Minimum wattage 5W/2V
www.istick.org/istick-30w.html

P.S if you are after some cheap boards FT have the following
Pico 75W $9.92
Topbox Mini 75W $10.20
Snow Wolf Mini 75W $15.03

[VapingBad]

should not the liquid travel through the centre/510 not where the kidney shaped holes are, maybe I'm missing something and the kidney shaped holes are just here to collect belly button fluff.

[Get Off My Cloud]

Dec 21, 2017 2:54:03 GMT VapingBad said:

should not the liquid travel through the centre/510 not where the kidney shaped holes are, maybe I'm missing something and the kidney shaped holes are just here to collect belly button fluff.

The kidney holes are for filling the bottle, note the o-ring on the top, when the RDA is in place it seals the top leaving the central hole the only path liquid can take when you squeeze the bottle.

[Lee]

If you read the comments on that video, it sounds like there were a batch of lower quality inserts and the manufacturers will replace them if they come out easily

[ibalders]

I would of thought if you used that on a mech mod you would get a good bit of voltage drop.