Favourite rebuildable dripper ?

[Deleted]

possibly a connector gromit seal from a vivi nova although that might still be too large ... the hole is very small about the width of a biro tip

[robby]

Mar 13, 2013 14:48:54 GMT @ashmal said:

possibly a connector gromit seal from a vivi nova although that might still be too large ... the hole is very small about the width of a biro tip

Definatley the right material

[Deleted]

Suck it and see is what I suggest - you may find it ok, just what I've found with it ... just tested mine and it's currently fine. The cool vape is because of the length of the device and positioning of atty I think. If you get an ego sized drip tip, you can use the ego fitting without the tank and reduce the length a touch more.

[robby]

Mar 13, 2013 14:57:37 GMT @ashmal said:

Suck it and see is what I suggest - you may find it ok, just what I've found with it ... just tested mine and it's currently fine. The cool vape is because of the length of the device and positioning of atty I think. If you get an ego sized drip tip, you can use the ego fitting without the tank and reduce the length a touch more.

Yes, looking at it, it is the only concern for me (the coil is a long way from the tip)

[Deleted]

In comparison to your venerable Vaporbreak Phoenix, the top of the Vision atomiser would approximately be where the Phoenix knurled part of the base is

[dave]

I've been using RDA's for ages and I still find they are hard to beat as well as being really easy to re-coil. I've had an Igo-L since the group buy and I've found that very good as well - it does wobble about a bit though! I've got an old dead eGo battery I use as a "puller", so with both of these I stick them on the puller to get them apart - especially necessary with the RDA.
I recently got a DRA-X through the classies and it is also a very good performer - much solider than the Igo and a nicely made attie. Apart from cosmetic differences it is a more or less exact copy of the Sattys that Perpy has pictured above. It has a screw fitting and the airhole lines up nicely at an angle to the coil : Highly recommended - it goes very well on a 22mm mech mod as well

[kurotoshiro]

Mar 13, 2013 0:00:15 GMT ibalders said:

I believe and I could be totally wrong but an air hole lined up is only really required on a mesh set up on a genesis style atty

I don't know about any other drippers, but it's certainly the case with the Clockworks RDA that you need the airhole lined up correctly (and pointed skywards when inhaling).

[ibalders]

Mar 13, 2013 15:50:40 GMT kurotoshiro said:

Mar 13, 2013 0:00:15 GMT ibalders said:

I believe and I could be totally wrong but an air hole lined up is only really required on a mesh set up on a genesis style atty

I don't know about any other drippers, but it's certainly the case with the Clockworks RDA that you need the airhole lined up correctly (and pointed skywards when inhaling).

That might be the case, but on my IGO-L for instance I do to begin with line the hole up, but depending on what type of juice I have in mine I adjust until I'm getting my desired vapour and taste, in my Phoenix dripper I have not notice a lot of difference where the hole is lined up, but as I said I could be totally wrong, buy hey it works for me :)

[robby]

Mar 13, 2013 16:49:58 GMT ibalders said:

Mar 13, 2013 15:50:40 GMT kurotoshiro said:

I don't know about any other drippers, but it's certainly the case with the Clockworks RDA that you need the airhole lined up correctly (and pointed skywards when inhaling).

That might be the case, but on my IGO-L for instance I do to begin with line the hole up, but depending on what type of juice I have in mine I adjust until I'm getting my desired vapour and taste, in my Phoenix dripper I have not notice a lot of difference where the hole is lined up, but as I said I could be totally wrong, buy hey it works for me

Stick two coils in the Phoenix and it wont matter where the air hole is lol. Works fantastic

[greendollar]

[Banky]

Don't own the Nimbus, I have the eBaron Dripper works out cheaper to buy, and a great dripper.

[Balllsy]

Mar 13, 2013 10:07:36 GMT chrisjw said:

Mar 12, 2013 23:58:31 GMT Balllsy said:

Well, I have a chrome Vamo, a ss Vamo and a Nutz 18350 and I can no longer use my igos on any of them as they have stripped the threads off all of my mods, so I'm thinking a screw on might be a better idea. S'atty looks good Perps, the bigger the better for me as I find it extremely hard to recoil with my eyesight.

I had that problem Sue & got an adaptor...............

LOL cheers Chris, only problem with the adaptor is it lifts the atomiser off the mod so doesn't fit flush.

[chrisjw]

Mar 14, 2013 14:27:48 GMT Balllsy said:

Mar 13, 2013 10:07:36 GMT chrisjw said:

I had that problem Sue & got an adaptor...............

LOL cheers Chris, only problem with the adaptor is it lifts the atomiser off the mod so doesn't fit flush.

Yeah, true, although I only use my dripper at home, so for me it didn't matter.

[Balllsy]

I have looked at the eternity Robby, but prefer the wider atomisers like the Nimbus. Love the look of Senio dripper... Very nice indeed