New DID Clone help needed

[maccafan]

Get a better atty..Honestly, these things are ok to begin with, but they are really shit..

Get an AGA-S. It's a superb atty..

[fecked off]

May 1, 2013 19:08:01 GMT maccafan said:

Get a better atty..Honestly, these things are ok to begin with, but they are really shit..

Get an AGA-S. It's a superb atty..

i second that i had to drill the wick hole out to 3mm just to get the bugger going

[kamikaze1100]

however my aga-s the top cap does not locate properly and looks the it's not been machined correctly, i did email vapegear but didn't ever hear anything back from 'em
so the long and short of it all is i aint ever used it

[fecked off]

is your aga the one with the threaded top cap?

[maccafan]

May 1, 2013 19:20:50 GMT kamikaze1100 said:

however my aga-s the top cap does not locate properly and looks the it's not been machined correctly, i did email vapegear but didn't ever hear anything back from 'em
so the long and short of it all is i aint ever used it

If it is the threaded type you can sand it down slightly to get the airhole to line up..

If it is the press fit type, maybe you just need a couple of different size O rings to sort it..

If you can't be arsed, I'll pay you a fiver for it..

[kamikaze1100]

tis press fit and i think that the part that the centre post and wick goes through has not been machined propper coz the cap's fine...
gunna see if i can fix it

[denis9t9]

May 1, 2013 9:14:27 GMT andy01424 said:

could also be the ss wick to tight try pushing a pin down the center,do also remember that its best to tilt the atty,but saying all this if you manualy wet wick then try it it works ,but then it goes hot burns a bit and tastes like uggghh,its boiling, take wick out give it a good heat up[have a safety pin pushed down center of it saves burning fingers] and then re wick,it sounds more like when you start vaping the ohms have dropped and its heating the wick faster than it can wet it,also give wire quick heat before using to

Ok had another bash last night re-rolled the mesh around a paper clip & re-oxidised the wick, kept the same coil as the wick slid out & back in again no probs, soaked the wick in juice fired it up & vaping well now, filled it up with juice & it tastes fine.
Only thing is it dries out quite quickly, plus when you put the filler screw back in it floods so will have to leave it out & keep it stood up, do they usually dry out fairly quickly without tilting it when you vape?

[andy01424]

when you use your vape your supposed to tilt it lol practically horizontal to help wet it also when vaping make sure wick is underneath,it also sounds like as mentioned not enough air gettiing through air hole,use a blade off nail scissors and gently prod in and twist, could be some swarf or cleaning stuff blocking it ,done it with all my clones and aga't and arashi lot better

[denis9t9]

May 3, 2013 11:20:39 GMT andy01424 said:

when you use your vape your supposed to tilt it lol practically horizontal to help wet it also when vaping make sure wick is underneath,it also sounds like as mentioned not enough air gettiing through air hole,use a blade off nail scissors and gently prod in and twist, could be some swarf or cleaning stuff blocking it ,done it with all my clones and aga't and arashi lot better

Cheers for that andy01424 i'l have another look this evening & check the air hole i was just afraid to open it out to much.

[monty]

Juice burns help. When you have finished a tankful put some juice or PG or VG on the wick and burn it, repeat 3 times.
Could be the steel used to make the atty. You can get a genuine AGA S for less than a DID clone.