Innokin iTaste vv/vw v3 and kanger t3s issue

[Village idiot formerly tjlumle]

Hi

I was wondering if anyone else has had any issue with the Innokin iTaste vv/vw v3 and a kanger t3s clearomizer as mine has just stopped working on me was working fine for a few days then today just started reading intermitently ie reading non on the screen instead of the ohm's

Any help would be great

Thanks
Tom

[jcol]

i can get this with my T3's on my evic, just pull the little metal centre pin down a little on the T3 and it will make contact again. (its up in the thread recess)
Just a little or else it will leak lol

Oh and welcome to the forum

[Village idiot formerly tjlumle]

I have tried your recommendation to no joy already. I have got an evod coming in the post hopefully tomorrow hoping I have more luck with that. It had been working fine for days I do swap about though so that have caused it to push up abit.

[jcol]

If its not been detected, then is a connection issue or a short has developed.
How about recoiling it, that can usually fix any problems

[Perpetua]

Have you pushed the centre pin on the battery down maybe Tom?


Welcome to you btw.

[Village idiot formerly tjlumle]

I have checked the battery pin and pulled it up slightly but still no joy.

[Village idiot formerly tjlumle]

Its working fine with my iclear 16 no problems, just having issues with the t3s

[Village idiot formerly tjlumle]

Jcol how do you go about recoiling it?

and thanks everyone for the welcomes

[dnglos]

Aug 4, 2013 21:26:22 GMT Village idiot formerly tjlumle said:

I have checked the battery pin and pulled it up slightly but still no joy.

You probably shouldn't go messing with the pin on the battery unless it's absoultely necessary. I'd start by checking that the T3 head is properly screwed into place and if that doesn't work you should try what jcol suggested above.

[Village idiot formerly tjlumle]

I took apart the t3s and retightened the coil and placed back on the battery and I am now getting an ohm reading then it appears it is leaking from the bottom which then is cutting out the ohm reading.

[dnglos]

Aug 4, 2013 22:02:59 GMT Village idiot formerly tjlumle said:

I took apart the t3s and retightened the coil and placed back on the battery and I am now getting an ohm reading then it appears it is leaking from the bottom which then is cutting out the ohm reading.

If you haven't done it already you should wipe of all the juice from the battery as soon as possible. As for the T3 it sounds like you might have over-tightened it and damaged an o-ring. It might be best to ditch that head and start again. If you've got a spare head I'd suggest you screw it in firmly (but not too tightly), then fill up the tank and leave it to stand on a paper towel overnight to check for leaks.

[Village idiot formerly tjlumle]

Thanks for the help I will have to buy a new head. I have dried the battery there was only a small leakage on the magnet which i have dried out. I will have a look at buying a new head for the t3s. I know wrong forum section but has anyone found a good benson and hedges replacement? I am currently enjoying wickedeliquids glace cherry and snickers flavours. Although I have found the snickers flavour to be more of a desert vape after a meal. As is on the sweet side

[Village idiot formerly tjlumle]

I believe the t3s bottom pin is the cause of the leak but only leaks when in use will try a new head and hope that rectifies. If not might be a start again with a new t3s, but will give the evod a go first if it comes in the post today.

[pegasus]

Aug 5, 2013 7:01:53 GMT Village idiot formerly tjlumle said:

I believe the t3s bottom pin is the cause of the leak but only leaks when in use will try a new head and hope that rectifies. If not might be a start again with a new t3s, but will give the evod a go first if it comes in the post today.

I love my evods but I did try the T3s and I can tell you that the problem is with the T3 ...! the base on the T3 wont work on a lot of ego  threaded  devices  I have tried it on all mine and It only works on 2 of the  battery's I have, it's the base that is too long and on most of my battery's it stops the coil  connecting  with the battery post.

To test my findings I fitted a T3's with a evod base and it work on every thing 

[Village idiot formerly tjlumle]

Can you buy the evod base by itself?