Nemesis Magnet Upgrade

[maccafan]

The switch throw is more a factor of how much the bottom pin has to travel to make contact with the bottom of the battery.

The entire switch mechanism should be snug against the bottom of the battery. The switch throw will be unaffected whether you use 2 or 3 x 1mm magnets. There is enough gap in the switch actuator mechanism to absorb an extra 1mm magnet and make no difference to the switch function. When assembling the switch, push the brass body down all the way and tighten the center pin as far as it will go, regardless of whether you are using the springs or magnets.

The contact pin should be tight when assembling the switch or is likely to unscrew itself causing the more serious issue of constant firing. I gently nip mine up with a pair of nose pliers to prevent this. Adjustments for differing battery lengths should be done my other means. Keep that contact pin on the switch tight.

If you have a shorter battery which is a flat top, remove the kick ring or extend the battery with a magnet if you want to keep the kick ring. For those with N35 magnets, use two magnets back to back on one side.

[Deleted]

I have gone back to using the original springs as I find that they perform quite well with a smooth action and they are able to support the weight without the need for the lock ring.
I had tried the 2 x N35 magnets .... too weak to support the weight
I had tried the 3 x N35 magnets .... supported the weight Ok but the switch action was too strong for the remaining half of my little finger (top half lost long ago in an argument with a table saw )

[chrisjw]

Dec 26, 2013 16:44:33 GMT spikus said:

I can't remember right now ... Their exterior diameter is 19 mm but not sure of the interior .. But the hole is too big which allows them to slide about... I need to get better fitting one methinks

I had some of those too spikus, but they kept moving around too much......I got these instead & they work perfectly........

www.ebay.co.uk/itm/171171387701?var=470309355556&ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649

[Super-Shiny]

Dec 29, 2013 10:24:21 GMT @freefromsmoking said:

I have gone back to using the original springs as I find that they perform quite well with a smooth action and they are able to support the weight without the need for the lock ring.

Same.

Until i get the N45 magnets as i don't have enough N35's to double up.

[Deleted]

Is the Nemesis from FT a good buy and can you recommend a good atty also from ft.
Thanks

[Deleted]

Dec 29, 2013 11:48:06 GMT Super-Shiny said:

Dec 29, 2013 10:24:21 GMT @freefromsmoking said:

I have gone back to using the original springs as I find that they perform quite well with a smooth action and they are able to support the weight without the need for the lock ring.

Same.

Until i get the N45 magnets as i don't have enough N35's to double up.

This guy is doing N42 magnets in the correct size  .... 10 for about £8 and free postage to UK 

www.ebay.com.au/itm/17-x-1-10mm-Hole-Ring-17x1mm-Ring-Strong-Magnet-N42-OD17H1ID10-/181289186314?#shpCntId

[Deleted]

Dec 29, 2013 12:10:04 GMT stamina said:

Is the Nemesis from FT a good buy and can you recommend a good atty also from ft.
Thanks

The Nemesis is so good that I have bought 3 of them. I can also recommend the Fasttech Ithaka and Taifun GT atties  ....  the Fasttech Kayfun 3.1 is also very popular although I bought the more expensive but better Ehpro version (imho) from Modsandatties. 

[Deleted]

Thanks @freefromsmoking

[Super-Shiny]

Dec 29, 2013 14:13:28 GMT @freefromsmoking said:

Dec 29, 2013 11:48:06 GMT Super-Shiny said:

Same.

Until i get the N45 magnets as i don't have enough N35's to double up.

This guy is doing N42 magnets in the correct size  .... 10 for about £8 and free postage to UK 

www.ebay.com.au/itm/17-x-1-10mm-Hole-Ring-17x1mm-Ring-Strong-Magnet-N42-OD17H1ID10-/181289186314?#shpCntId

Already got 10 on order with a GB on UKV for £6.50 delivered...should be due in sometime in January, ain't in no rush.

[Greg]

Dec 29, 2013 7:59:04 GMT maccafan said:

The switch throw is more a factor of how much the bottom pin has to travel to make contact with the bottom of the battery.

The entire switch mechanism should be snug against the bottom of the battery. The switch throw will be unaffected whether you use 2 or 3 x 1mm magnets. There is enough gap in the switch actuator mechanism to absorb an extra 1mm magnet and make no difference to the switch function. When assembling the switch, push the brass body down all the way and tighten the center pin as far as it will go, regardless of whether you are using the springs or magnets.

The contact pin should be tight when assembling the switch or is likely to unscrew itself causing the more serious issue of constant firing. I gently nip mine up with a pair of nose pliers to prevent this. Adjustments for differing battery lengths should be done my other means. Keep that contact pin on the switch tight.

If you have a shorter battery which is a flat top, remove the kick ring or extend the battery with a magnet if you want to keep the kick ring. For those with N35 magnets, use two magnets back to back on one side.

You can buy a longer top contact to retain the kick ring if necessary www.surinternet.com/epages/box13653.sf/sec9c9fc69a1c/?ObjectPath=/Shops/box13653/Products/215

[Super-Shiny]

Here also Greg www.atmomixani.gr/index.php/en/menu-shop-en/vmcategory-manufacturer-atmomixani-eg/long-upper-detail.html with plenty of other stuff: www.atmomixani.gr/index.php/en/menu-shop-en/vmcategory-manufacturer-atmomixani-eg/nemesis/nemesis-devices.html

[Greg]

Dec 29, 2013 18:47:38 GMT Super-Shiny said:

Here also Greg www.atmomixani.gr/index.php/en/menu-shop-en/vmcategory-manufacturer-atmomixani-eg/long-upper-detail.html with plenty of other stuff: www.atmomixani.gr/index.php/en/menu-shop-en/vmcategory-manufacturer-atmomixani-eg/nemesis/nemesis-devices.html

Looked at that yesterday but 14.99 shipping ! French link is 4.50 shipping  or was it 5.50:D

[Super-Shiny]

Oops i forgot about their shipping costs Greg

[testdruif]

Dec 29, 2013 11:48:06 GMT Super-Shiny said:

Dec 29, 2013 10:24:21 GMT @freefromsmoking said:

I have gone back to using the original springs as I find that they perform quite well with a smooth action and they are able to support the weight without the need for the lock ring.

Same.

Until i get the N45 magnets as i don't have enough N35's to double up.

shiny

Do you know what kind of magnets Atmomixani ships? (is it N35 or N45)?

[Super-Shiny]

testdruif i believe it is N45