Rebuidables Help Opinions

[danliddle]

Was looking in to Rebuildable Atomizers and just curious which is easiest atty to learn on ? & been reading a bit about it about the Kanthal Wire & Jap Organic Cottons and a bit confused by the Guages ? does each Atomizers use different Gauges etc like does it change the OHMs Resistance etc  or what ever & whats the difference between doing your own coils and buying them pre made like for e.g a Aspire coil can anyone help out cheers

[Get Off My Cloud]

A single coil setup would be easiest, i really like the Lemo and Lemo drop at the moment but there's a whole bunch of ati's you could single coil on.
The thicker the wire the lower the resistance.
Have a play with these online calculators so you can see how many wraps you will need for a desired resistance with various gauges.
www.steam-engine.org/coil.asp
coiltoy.ermeso.com/
The difference is it's cheaper to make your own and more versatile, premade coils come usually in 2 or 3 different resistance levels where you can make your own at any level you like.
Premade are obviously more convenient though.

[aliscampbell]

What tanks are you using now danliddle? I started rebuiding my kanger clearo's first, saves money and gives a much better flavour. I then moved onto rebuildables.

[Deleted]

As someone who couldnt coil for toffee a little while back, I'd say the taifun GT. Not only is it easy to coil but easy to refill too. I use premade coils

[markm]

The Thicker the wire, the lower the resistance.
The longer the wire, the higher the resistance.
More coils the longer the wire used to make it.
The lower the resistance the lower the voltage needed to evaporate the liquid.
The lower the resistance, assuming voltage is unchanged, the higher the Watts.

[danliddle]

So if I want the resistance down to .5 what guage would I get and cheers for the help and comments everyone I was looking at the Lemo and Kayfun and Taifun g2. The attys I use at the moment are Aspire Nautilus and Aspire Atlantis

[danliddle]

Jan 17, 2015 16:07:13 GMT aliscampbell said:

What tanks are you using now danliddle? I started rebuiding my kanger clearo's first, saves money and gives a much better flavour. I then moved onto rebuildables.

Mini Nautilus and Atlantis 

[aliscampbell]

Their not simple to rebuild, prob best start with a kayfun, have a look at this guide from Tom link

I use .25 and .3 wire mostly.

[arron]

I would suggest a kayfun for your first rba, it's nearly impossible to get a bad vape and will happily take .25mm-.4mm wire

[Clivia]

thanks for this thread danliddle - cause I have the same questions - and a major one is where to buy what ? bought a kayfun clone form FT - which ended in the bin as it was leaking all over

[moodyb]

Jan 17, 2015 16:24:08 GMT danliddle said:

So if I want the resistance down to .5 what guage would I get and cheers for the help and comments everyone I was looking at the Lemo and Kayfun and Taifun g2. The attys I use at the moment are Aspire Nautilus and Aspire Atlantis

The gauge will depend on how many wraps you want or need in your coil/s.

What mod are you using the Nautilus & Atlantis on?

[aliscampbell]

As to kayfuns, I bought this clone and it has been fantastic, not drop of juice lost link

I've been looking at this one for more airflow link

[aliscampbell]

There is also a few kayfun's in the classified section, might be worth a look

[danliddle]

So you would use 25 mm of Gauge ? for Kayfun

[danliddle]

Jan 17, 2015 16:47:55 GMT aliscampbell said:

Their not simple to rebuild, prob best start with a kayfun, have a look at this guide from Tom link

I use .25 and .3 wire mostly.

I checked that out earlyer I was thinking about a Kayfun to start with as all the people recomend and what does that mean 25 and 3 wire what does this mean ?