robby
Super Member
International Bargain Master
WISMEC? Check out the Member`s Only thread.
Joined:September 2012
Posts: 13,815 
Location:
Likes: 8,652
Recent Posts
Last Online Jun 24, 2013 9:58:00 GMT
|
Post by robby on Dec 15, 2015 11:21:03 GMT
|
|
yourgurnard
Super Member
Joined:November 2014
Posts: 1,295
Location:
Likes: 1,026
Recent Posts
Last Online Dec 14, 2023 23:26:20 GMT
|
Post by yourgurnard on Dec 15, 2015 17:40:53 GMT
TBH, I'm glad it's not parallel.....only had My new Abaddon clone 3 days & might've got dis-satisfied!  |
|
enjay
Super Member
Joined:December 2013
Posts: 2,372
Location:
Likes: 1,113
Recent Posts
Last Online Sept 22, 2024 21:38:04 GMT
|
Post by enjay on Dec 17, 2015 1:06:40 GMT
Cracking little mod, got the mini buddha sitting on mine with a 0.35 build
|
|
letsavit
MOVED ON
Blue Plonker
screw calm and get angry
Joined:February 2015
Posts: 4,720
Location:
Likes: 3,860
Recent Posts
Last Online Mar 25, 2015 21:45:41 GMT
|
Post by letsavit on Dec 17, 2015 1:31:44 GMT
Ordered,this could be worst for experienced than beginners, all my duels mechs are parallel. Got break habit now or blow meself up....!
|
|
letsavit
MOVED ON
Blue Plonker
screw calm and get angry
Joined:February 2015
Posts: 4,720
Location:
Likes: 3,860
Recent Posts
Last Online Mar 25, 2015 21:45:41 GMT
|
Post by letsavit on Dec 17, 2015 1:32:54 GMT
TBH, I'm glad it's not parallel.....only had My new Abaddon clone 3 days & might've got dis-satisfied! You got one then, mine was from3fvape, nice in it .... |
|
enjay
Super Member
Joined:December 2013
Posts: 2,372
Location:
Likes: 1,113
Recent Posts
Last Online Sept 22, 2024 21:38:04 GMT
|
Post by enjay on Dec 17, 2015 3:26:04 GMT
Ordered,this could be worst for experienced than beginners, all my duels mechs are parallel. Got break habit now or blow meself up....! They're absolutely fine, just got to make sure the positive pin of the atty sticks out further than the body for the hybrid part and build higher because it's series. 0.3 and up is sweet. I always screw the top cap to the atty first, nice and tight, batteries in, positive pin facing up for the atty side. I then screw the atty down then back it out to where I want it to sit. I'll then screw the button on nice and tight. The bottom contacts piece can rock so when you tighten the switch it tightens the atty too. But yeh, no worse than any other mech. |
|
yourgurnard
Super Member
Joined:November 2014
Posts: 1,295
Location:
Likes: 1,026
Recent Posts
Last Online Dec 14, 2023 23:26:20 GMT
|
Post by yourgurnard on Dec 17, 2015 16:44:30 GMT
TBH, I'm glad it's not parallel.....only had My new Abaddon clone 3 days & might've got dis-satisfied! You got one then, mine was from3fvape, nice in it .... Mine's not as nice-looking as Your one.....the £10.00 ali. one. |
|
