|
|
Post by warlordxxx - (Mark) on Nov 22, 2012 0:02:12 GMT
Hey Dizzi - wow good job i'm impressed thanks for the kind words and have to say i'm glad you made the mod you wanted - Awesome job
|
|
|
|
Post by warlordxxx - (Mark) on Nov 18, 2012 12:54:58 GMT
That is a stacked battery mod.. So take some basic precautions and keep the battery as a pair, check them both every time after you charge to make sure the voltages are the same and drill some holes in the tin on either side where the batteries are located I hope you have used a fuse of some kind too.. Macca the boards have under-current, short and thermal protection built in - It's the same one the lovely Garry Dibley tested out  |
|
|
|
Post by warlordxxx - (Mark) on Nov 16, 2012 1:01:13 GMT
I made a tine single 18650 ut dont get much vapor Used same insides as yours but didnt get a display  So hopefully once ive put it on steve multi meter it will be low, so up it get more vapour,,, hopefully Although my soldering aint up to much either Mat Quick question Mat - you used two batts with the vv board right - It's step down ie more current in that out ? |
|
|
|
Post by warlordxxx - (Mark) on Nov 5, 2012 12:54:36 GMT
I have just rigged up a couple of atties with one about 1.5ohms and one at 2.8ohms that I can put my multimeter on while in use on a battery. So I`ll be getting an "on load reading". Be interesting to see how they test out The z-max is a pulse mod so the readings that you get won't mean much i'm afraid |
|
|
|
Post by warlordxxx - (Mark) on Oct 31, 2012 20:06:51 GMT
Andy that's great mate and a lot of users will have no issues although it feels like its hitting a lot harder than it actually is - some people though if after a very low voltage for things like 306 attys will just taste burnt every time because they simply can't get a voltage low enough
|
|
|
|
Post by warlordxxx - (Mark) on Oct 31, 2012 19:35:17 GMT
All good stuff i agree,i had mine from ECW and they didnt issue a recall so i thought i would check.To be honest i cant say i have had any issues on my ZMAX,i checked the outputs and they were well within normal limits.Possibly its just a bad batch?ECW did say however that if i was having issues to return it . Andy when you say you've checked it what did you check it with mate ? |
|
|
|
Post by warlordxxx - (Mark) on Oct 31, 2012 17:49:31 GMT
Andy this isn't a recall from Smok - this is a recall from Alba it would seem because they are just as unimpressed with the voltage settings being off as quite a few others and i have to say kudos to them for doing so. In my book it speaks volumes |
|
|
|
Post by warlordxxx - (Mark) on Oct 30, 2012 2:41:21 GMT
Thanks Sandra i love that tip it's quite slim unlike a lotta the mings i've tried and fits lovely on the lips
|
|
|
|
Post by warlordxxx - (Mark) on Oct 30, 2012 1:29:01 GMT
Thanks Gordy - can't take credit for the idea it was requested by Sahil i'm just the facilitator lol
|
|
|
|
Post by warlordxxx - (Mark) on Oct 30, 2012 1:09:19 GMT
Ok i've been working on this one for quite a while now - It was made for Sahil a wonderful vaper all the way from India . Case is all vapages work i just added a few extra touches   I enlarged the top hole to take a 19 x 35mm tank (when fitted the cap is level with the top of the hole) - It has a 3mm flathead LED behind the tank to light it up and get an idea of the amount of juice left in the tank.  You can make out the Swadj circuit behind the polycarb - the polycarb is in there to stop Sah putting his fingers inside the hole left by the now not present bottle.  You can just about make out the pot adjustment hole underneath . This mod took me waaaay longer than it should have done but i only had one v-mod so if i killed it it was truly dead lol. I have to say the original V-mod is wonderfully constructed . The plastic inside cut like butter with a dremel but sanding it afterwards took forever it's very strong and durable so i hope Vapage aren't upset with what i've done to their mod but if you want a really strong well made bottom feeder i really would recommend it |
|
|
|
Post by warlordxxx - (Mark) on Oct 28, 2012 20:49:56 GMT
Hehe once it's finished you will be the first person to see it hows that:)
|
|
|
|
Post by warlordxxx - (Mark) on Oct 28, 2012 20:47:42 GMT
Sorry mate but this one has to be a secret for now |
|
|
|
Post by warlordxxx - (Mark) on Oct 28, 2012 20:17:03 GMT
Wait til you see my next plan something that could be right up your street oh?? do tell  Hehehe this one you will have to wait and see  |
|
|
|
Post by warlordxxx - (Mark) on Oct 28, 2012 20:05:22 GMT
Guilty - i was at work all day - Sorry i'll get me coat lol it's hung by the door third hook from right  Lmao was good to talk to you the other night Paul |
|
|
|
Post by warlordxxx - (Mark) on Oct 28, 2012 20:00:33 GMT
lol I had my coffin mod out a little while ago, which the sister in law loved, as did my 14 year old niece, was funny seeing the look on everyones faces Wait til you see my next plan something that could be right up your street |
|
