Rose v2 clone

[Deleted]

Lee at Eden must have been telling me porkies then.

[decoy]

ive tried all sorts in my clone and tbh its been like using silk cut when your a b and h man(chimney,twisted,parallel, duel and good old single miro coil with all sizes of wire)
but ive had a eureka moment with it(stuck it lucky more like).5 wire on a 2.5mm bit at .5ohm and it kicks
oh and ive played with the height of the coil as well now sat bang in middle of slots
think im finally happy to take it out as my only atty

[mxethey]

Oct 10, 2014 21:42:28 GMT macmagoo said:

Oct 10, 2014 21:33:31 GMT mxethey said:

macmagoo If you haven't tried it yet give it a try yourself and see what you think

I'm vaping a Rose V2 at the moment and the coil sits about 2mm from the air hole and there is very little throat hit with 12mg Digby's Apple & Cinnamon Pudding.

The bottom part of the coil is a nats cock below the bottom of the wick cut outs vaping with house of liquid cinnamon cookie 12mg and plenty of throat hit, when i used less cotton and pushed the coil down just above the air hole the throat hit and harshness was to much.
By the way i'm vaping on the rose v2 i bought from you mate and its great.

[robdelmar]

Oct 6, 2014 19:02:40 GMT macmagoo said:

You would be better getting the O'rings that Andy Hobbs suggested on Facebook.

Cant find it, is there a link

[Deleted]

Oct 11, 2014 20:32:17 GMT robdelmar said:

Oct 6, 2014 19:02:40 GMT macmagoo said:

You would be better getting the O'rings that Andy Hobbs suggested on Facebook.

Cant find it, is there a link

These work and this list is thanks to Dan cheers mate

eBay
370859623567
321169731773

.All 1mm cross section.

510 - 2.5mm
Chimney -7mm
Coil body top and tank section - 15mm



Coil body bottom and air control ring -18mm. Again 1mm c/s

[ringading]

Hope arron is still into getting spares for the Rose. Tanks, ceramics and o-rings.

[Ron]

The pleasure when you complete a build.Anyone else finding the grub screws soft

[robdelmar]

Oct 11, 2014 22:49:26 GMT @tazmania441 said:

These work and this list is thanks to Dan cheers mate

eBay
370859623567
321169731773

.All 1mm cross section.

510 - 2.5mm
Chimney -7mm
Coil body top and tank section - 15mm



Coil body bottom and air control ring -18mm. Again 1mm c/s

Thanks for that @tazmania441 and Dan, got all but 7mm, wont bother with the 2.5 as I,ve managed to strip the thread on the 510 pin & replaced with a m2 brass bolt & 2mm x 1mm o ring

[Deleted]

Oct 12, 2014 15:53:45 GMT Ron said:

The pleasure when you complete a build.Anyone else finding the grub screws soft

Yes they are, but they are like that on the genuine. Just don't over tighten them or they wont come back out.

[decoy]

made up some fresh twisted 2 lengths of .25 and 2 of .4 all twisted together to make a mad .5 ohm coil
so want to put it in but got the rose working well with a .5 micro coil at .5
i need a second one

[Deleted]

Oct 13, 2014 17:23:32 GMT decoy said:

made up some fresh twisted 2 lengths of .25 and 2 of .4 all twisted together to make a mad .5 ohm coil
so want to put it in but got the rose working well with a .5 micro coil at .5
i need a second one

Ive got one in the classies

[decoy]

this stuff is nuts
but i dont know what the thickness is but its 1mm wide
not the easiest stuff to work with but that is a .8 ohm coil and it hits

[iLardyboy]

Struggling to get a great vape from the Rose, I'm probably doing something wrong. Have it set up with 0.3 kanthal 1.4ohms, the flavour is decent but I'm getting a better vape from my Kayfun. Would thicker wire be better for this atty? Really want to get this setup right, at the moment it's just ok. Any advice would be great.

[Greg]

Nov 2, 2014 19:57:15 GMT iLardyboy said:

Struggling to get a great vape from the Rose, I'm probably doing something wrong. Have it set up with 0.3 kanthal 1.4ohms, the flavour is decent but I'm getting a better vape from my Kayfun. Would thicker wire be better for this atty? Really want to get this setup right, at the moment it's just ok. Any advice would be great.

What's poor about it, I found it easy to mount the coil too low and it really restricts airflow and vapour. Try lifting the coil a little by pulling it up gently with tweezers, makes a big difference for me.

[Greg]

I also use a 3mm diametre coil with doubled over Rico cotton, this gives four Rico tails and it's the perfect size for the Rose juice channels