Lilac
Super Member
~If it feels good...do it...~
Joined:November 2009
Posts: 3,348
Location:
Likes: 2
Recent Posts
Last Online Oct 14, 2015 11:16:59 GMT
|
Post by Lilac on Feb 8, 2012 22:39:46 GMT
It's murder when u feel that your mod isn't working well for you while you're fiddling about with the pin etc girls, don't forget the cleaning of the centre post and the bit of the button that touches it....that simple tip always makes a big difference to the performance of my GG's
|
|
bluemagnum
Super Member
Joined:April 2011
Posts: 2,094
Location:
Likes: 641
Recent Posts
Last Online Jun 9, 2024 16:01:50 GMT
|
Post by bluemagnum on Feb 8, 2012 22:41:11 GMT
I'll explain this the best I can without pictures. Remove atty/carto from ggtb Remove top cap Inside the cap you will see a hexagon nut, unscrew that a few turns but don't take it completely out, they can be a pain to get back in as you're screwing back into a plastic part. (you may need pliers to unscrew it, just re-tighten it finger tight) Put atty/carto back on top cap and screw all the way in Try to draw on atty, if it's tight, back it off till you can draw on it as you would like to vape it. Once done, re-screw pin back in. Place top cap back on and hopefully, all will be ok.
|
|
beeper
Super Member
Joined:August 2010
Posts: 871
Location:
Likes: 269
Recent Posts
Last Online Oct 6, 2024 23:28:57 GMT
|
Post by beeper on Feb 8, 2012 22:45:59 GMT
I shall certainly take on board what has been said and report back. But last try, the hex nut on the 510 fitting is stuck solid
|
|
eyebrook
Super Member
Lounger
Joined:June 2011
Posts: 625
Location:
Likes: 151
Recent Posts
Last Online Jul 16, 2013 16:50:43 GMT
|
Post by eyebrook on Feb 8, 2012 22:50:06 GMT
If your using 14500 batts in the GGTB put the telescope bit on top of the batt, if its still not good open the telescope a bit untill you have a good contact and the top cap still screws down tight, hope this helps
|
|
Lilac
Super Member
~If it feels good...do it...~
Joined:November 2009
Posts: 3,348
Location:
Likes: 2
Recent Posts
Last Online Oct 14, 2015 11:16:59 GMT
|
Post by Lilac on Feb 8, 2012 22:52:07 GMT
Think Hissie uses 17670's Eyebrook
|
|
beeper
Super Member
Joined:August 2010
Posts: 871
Location:
Likes: 269
Recent Posts
Last Online Oct 6, 2024 23:28:57 GMT
|
Post by beeper on Feb 8, 2012 22:56:26 GMT
yes, me too.
|
|
eyebrook
Super Member
Lounger
Joined:June 2011
Posts: 625
Location:
Likes: 151
Recent Posts
Last Online Jul 16, 2013 16:50:43 GMT
|
Post by eyebrook on Feb 8, 2012 23:02:04 GMT
Ok then turn the batt spring around so its tighter, sticks up more if its not already that way around, never had to adjust the centre pin in my GGTB, so I dont know a lot more sorry
|
|
bluemagnum
Super Member
Joined:April 2011
Posts: 2,094
Location:
Likes: 641
Recent Posts
Last Online Jun 9, 2024 16:01:50 GMT
|
Post by bluemagnum on Feb 8, 2012 23:10:40 GMT
Ok then turn the batt spring around so its tighter, sticks up more if its not already that way around, never had to adjust the centre pin in my GGTB, so I dont know a lot more sorry Mine was too long, I chopped about 4mm off it.
|
|
hissie
Super Member
Joined:July 2010
Posts: 4,601
Location:
Likes: 120
Recent Posts
Last Online Apr 22, 2021 20:41:37 GMT
|
Post by hissie on Feb 8, 2012 23:36:28 GMT
Think Hissie uses 17670's Eyebrook Yup that's right lilac. Never needed to use the telescopic bit as vaping at 3.7 v is enough for me. Although I've been vaping nearly two years, I'm still pretty new to all the workings as I've been a stickler with my tornadoegoriva batts. I pushed the boat out trying DC carts lol.
|
|