istick passthrough stand

[giles]

All right, so what's your solution?

[igual]

I like that, often thought of making a mod out of Lego.
Been looking at moving it back to back so you could glue together but have a proper flat base plate both sides front facing.

[VapingBad]

Right angle micro USB adapters are hand for this

[prr]

igual Martin leave the Lego alone, you know what happened last time!!!

[giles]

Trouble is, my grandson is going to want his lego back sooner or later

this is neater, but I don't know how long it will last:



It's a modified one of these.

[qsplan]

what about this one? a 3D printed base for iStick....

[giles]

It's all greek to me qsplan. Also, it doesn't show the mini usb connection, but it looks more like a charging station. I'm after something that I can put it into in between vaping on the pass-through. I suspect with that device you'd have to pick the whole thing up while you were vaping, which would be a bit of a handful.

If you have a 3d printer there's a spec here (I think), but I don't have one of those.

There's a guy on Reddit who puts a big office clip over the bottom, which might work well if you had an angled mini-usb like VapingBad suggests.

And there's a video here about a stand called Boris, but it's a bit tilted and my goliath is inclined to leak through the air-holes if its at an angle.

[VapingBad]

Jun 23, 2015 21:07:43 GMT giles said:

It's all greek to me qsplan. Also, it doesn't show the mini usb connection, but it looks more like a charging station. I'm after something that I can put it into in between vaping on the pass-through. I suspect with that device you'd have to pick the whole thing up while you were vaping, which would be a bit of a handful.

If you have a 3d printer there's a spec here (I think), but I don't have one of those.

There's a guy on Reddit who puts a big office clip over the bottom, which might work well if you had an angled mini-usb like VapingBad suggests.

And there's a video here about a stand called Boris, but it's a bit tilted and my goliath is inclined to leak through the air-holes if its at an angle.

You can use polymorph to eaisly make a base with the angle adapter, it just a therom plastic that comes in beads you put in hot water until it goes clear then you can shape it and it sticks to lots of plastics very well,  I can bring some to the london meet if you like Giles if you want to have a go.

[wight]

Jun 23, 2015 16:35:23 GMT igual said:

I like that, often thought of making a mod out of Lego.
Been looking at moving it back to back so you could glue together but have a proper flat base plate both sides front facing.

I keep thinking about a Meccano mod

[giles]

That's kind VapingBad, but I already have some polymorph. I'm pretty incompetent with it but I'll give it a try if the thing above fails.

[VapingBad]

Jun 23, 2015 23:00:59 GMT giles said:

That's kind VapingBad, but I already have some polymorph. I'm pretty incompetent with it but I'll give it a try if the thing above fails.

Whenever I use it I spend most of the time with a heat shrink heat gun smoothing the finish, but it does the job, just not neatly in my case.

[Ron]

www.fasttech.com/p/1916203

[VapingBad]

Jun 23, 2015 23:11:01 GMT Ron said:

www.fasttech.com/p/1916203

Something useful I missed on FT , that's what I use the right angle adapter for 90% of the time a phone stand and the USB is the right way round for my phone, but you would have to modify/cut the top to fit an iStick.

[Ron]

istick 20 is a staight fit on

[phatfil]

Jun 23, 2015 16:35:23 GMT igual said:

I like that, often thought of making a mod out of Lego.
Been looking at moving it back to back so you could glue together but have a proper flat base plate both sides front facing.

GLUE?  LEGO and GLUE?   Not awsome  u cant have seen THE lego movie  if u had u would know only the 'Evil' use glue on leggo..   Or do u wear a cape and twiddle your long waxy tash when cackling?