Recent Posts

Its gonna be active at 5am gmt I believe according to the fasttech forums, 20 mins to go!

I saw in VapnFagan's review that the coil head contains some cotton too, so not all ceramic
so the coil is wrapped in cotton then with ceramic around it, it seems. So I wonder if anything found in the report could be either the ceramic or the cotton or even the nickel wire, rubber insulator. Would be good if they did a side by side test with a coil from another manufacturer too to compare such as a nickel head or kanthal head.
Its possible to test the coil they have to test differently than a kanthal head since it uses nickel wire so needs to be below a certain temperature.

The OBS Crius was sent by gearbest for purposes of review, its available in 3 colors - Black, White, Silver from www.gearbest.com/rebuildable-atomizers/pp_257254.html
The price is at $22.49 currently using coupon: 2015Xmas

(Flash Sale for the silver or black version is currently running for $20.99)





The OBS Crius is a top fill 22mm RTA with a similar deck to the Velocity RDA allowing easy coiling with dual coils. Its made from 304 grade stainless steel and pyrex glass for the 4.2ml capacity tank and drip tip with either no paint for the stainless version or black or white paint for those corresponding versions. The deck also has 4 areas where the tails of your wick can be placed easily so it will stay in place when screwing the base back to the rest of the tank. The juice channels have holes instead that feed the wicks and the chimney has corresponding holes that reveal or hide the juice holes in order to control the juice flow.







The RTA comes in a clam shell plastic packaging protected in foam with a spare pyrex glass tank, theres also a small hex driver to tighten the grub screws for the coil legs. Underneath the first foam insert are some more accessories like spare o-rings, screws, some wire and pre made coils. Theres also another bag with some organic cotton next to it.



The design of the juice channels made it very easy to place the wicks and the juice control only requires a small twist of the glass section in order to close and open the channels. The posts are great for coiling as the coil legs do not share the same holes. The holes are large too, so larger diameter wires should fit easily as well as parallel wires, twisted wire, claptons, fused claptons etc. The holes go all the way through the posts however so you can see the sides of the wire and both ends of the grub screw. In theory this could cut short some thin gauge wire but with 0.45mm (awg25) wire it seemed fine. Just make sure when tightening the grub screw to not over tighten them. When tightening just go slowly and wiggle the coil leg left to right and up and down a bit and if the coil does not move at all then it should be tight enough. Also with clapton coils they were fine to install but the diameter being 2.5mm required installing the clapton coils quite close to the posts in order to provide enough clearance for the chimney. With the awg 25 wire with 7 wraps around 2.5mm the coils installed easily and the resistance was 0.33ohms overall.









The top fill port is easy to access without any screwing just by pulling up the top section and the fill port is large to allow most bottles to be used as well as air on the side. Then to close you just push the top down and theres an o-ring to keep juice from leaking. Its best to close the juice flow control when filling though as it can leak the whole tank quickly depending on the juice consistency. They also do recommend closing off the juice flow when leaving the tank overnight - with 75% vg it did not seem to leak after a day or so but maybe long term it could.



The airflow is adjustable and is a good amount under the coils too but when vaping alot in a short period of time the included drip tip did get quite hot at 40 watts+ but would have been hotter if it was all stainless. The tank can apparently vape fine at high power at even up to 100 watts but I did not test it that high.



The flavor was good from the rta with no muting or dry hits even with a bit of cotton in the wicking channels. Its best to cut the wick at an angle though to avoid the juice getting constricted and place some of the cotton then in the juice channels, you can even push the cotton up a bit after its in place so not too much of it is in each channel.



The construction seems good with the fill port not being hard to open as well as the whole tank screwing together well. The only part that was tricky to unscrew at first was the parts on either side of the pyrex glass in order to remove the glass but after a few times it became easy to remove. Its tricky to get a grip of the top section as the area that holds the top port does spin around and has no locked position so you may need to use a rubber band/rubber gloves the first time to get a firm grip. The tank comes in not too many pieces so its easy to clean rather than having many small parts. The base can also be removed easily for changing out the cotton and changing your build too. At the the bottom of the tank is a plated 510 thats slightly protruding but not adjustable. When cleaning the tank especially, the o-rings are clear so it could be possible to misplace them so I'd recommend removing them from the glass carefully. The tank however was clean when received but its always a good idea to clean all the parts of a tank the first time and also occasionally after some use.







There were 1 or 2 versions or batches of the crius before the one with the velocity style deck and it seems thats the main difference between them as well as the drip tip hole now being compatible with other 510 drip tips where the previous one was slightly narrower than the standard drip tips so you could only use the included one. Also the fill hole is apparently a bit larger in the latest one.



Overall its a great tank thats easy to build on and fill especially compared to many other tanks

For other reviews and daily deals feel free to check out www.bestnewmods.com
Also the facebook group at www.facebook.com/groups/bestnewmods/

I tried that at the time too in concentrate and pre made and also found the same results, it must have had alot less caffeine than this eagle energy one unless the people who tried it experienced placebo effects maybe heh

I think though the caffeine they use must be a purer form than just crushing a caffeine pill as those contain binders and other things to keep them in tablet form. It sounds interesting having some fast acting caffeine though but generally a strong coffee does not take too long to work. It sounds like theres a huge amount of caffeine in that ecig if only 20 puffs is equivalent to 95-200mg, thats like 3-6 cans of coke lol and they claim up to 500 puffs in total, even 200mg worth can be very strong and lead to od symptoms if taken in 1 go.

So it seems all my assumptions were completely wrong lol, so its just an inhaler shaped like a cigarette with compressed gas and no electronics.



My Kayfuns have decided to constantly leak lately from every seal lol I think the o-rings need to change or something. The lemo v1 is not bad though for mtl but a bit airy like the kfv4, maybe even a bit more, but no leaks. Its really unbelievable that the tank with the smallest air flow and juice channels leaks the most!

Yea the larger xcube 2 needed you to register then pay for the upgrade which came to about $1 which is not bad but some people couldnt always get the app to connect well, I think with a new-ish phone it might work better. I saw on pbusardos latest vid of the xcube mini that he didnt mention having to upgrade though, was thinking maybe they did away with that, seems they probs don't make much profit really at $1 a pop and just adds the extra hassle.

At the moment alot of people are recommending stainless steel for temp control quite a bit as its an easier wire to work with than nickel and is supposed to not be unsafe if used in power mode unlike nickel.
Theres a few types of stainless steel wire though usually 316L or 317L so not sure which one the mod will be more accurate to use but you can also change the tcr in the mod to make it more accurate.

Real nice deal on that one, I guess theres less demand now with the dna 200 being out so its a good time to get the previous versions of mods
That British Express I think is just a name they call it at gb, it uses yodel in the UK I believe. I think most of the other options are fine (around 2 weeks) but China post can be very slow.